ALWAYS MAKE SURE YOUR WEAPON IS UNLOADED AND ALWAYS WEAR EYE PROTECTION!

1 - 12 of 12 items
Sort By:
1911/2011 Full Length Guide Rod Takedown Pin AK Trigger Slave Pin - Greatly Simplifies Trigger Installations
1911/2011 Full Length Guide Rod Takedown PinAK Trigger Slave Pin - Greatly Simplifies Trigger Installations
An increasing number of 1911 and 2011-style pistols are using a full length guide rod that requires the insertion if a pin to capture the reverse plug during disassembly. While some guys will fashion a pin from a paper clip, our solution is more...

If you have ever tried to assemble an AK and install the trigger, you know how challenging it can be to keep the disconnector and spring assembly properly aligned while sliding in the trigger pin. We have a far simpler solution for you. We've...

$2.49

$3.99

AR trigger slave pin - makes installation a breeze Installation Tool for Magpul Friction-Lock Stocks
AR trigger slave pin - makes installation a breezeInstallation Tool for Magpul Friction-Lock Stocks

This slave pin is used to assemble the trigger group outside of the AR so you could the trigger, disconnector and spring as a group. Once inserted in the lower, you push the normal trigger pin in and as it goes in, it pushes the slave pin out the...

Magpul makes some great stocks for AR rifles - especially the collapsible stocks with friction locks. The ACS, ACS-L, CTR, and STR family of stocks all have a lever in the front that when pressed locks the buttstock firmly to the recoil tube....

$3.99

$2.99

Polymer80 7" Nippers-Custom Ground to Flush Cut Top Rail Blocks Polymer80 8" Nippers-Custom Ground to Flush Cut Top Rail Blocks
Polymer80 7" Nippers-Custom Ground to Flush Cut Top Rail BlocksPolymer80 8" Nippers-Custom Ground to Flush Cut Top Rail Blocks

Sharpened nippers are the fastest way to remove the top rail blocks from Polymer80 frames. Now you may be wondering why I bothered to do some with a custom grind - most nippers have jaws that are beveled on both sides for strength. When you look...

Sharpened nippers are the fastest way to remove the top rail blocks from Polymer80 frames. Now you may be wondering why I bothered to do some with a custom grind - most nippers have jaws that are beveled on both sides for strength. When you look...

$24.99

$29.99

Polymer80 Nippers - 10" Discontinued Polymer80 Pistol Frame Barrel Block Channel Sanding Kit
Polymer80 Nippers - 10" DiscontinuedPolymer80 Pistol Frame Barrel Block Channel Sanding Kit

Sorry folks, I can't find a good source for 10" nippers to grind down so these are discontinued for now. I do have 7" nippers that I can grind down and they work just fine. Click here to go to the 7" flush cut nipper listing. Sharpened nippers...

Polymer80 pistol frames are fun to build. For a smooth functioning and reliable pistol, it is critical to clear out the Barrel Block in the middle channel of the frame and not leave any ridges that the recoil spring may hang up on. To help with...

$0.00

$15.49

Polymer80 Pistol Frame Barrel Block Channel Sanding Kit -Refills Polymer80 Pistol Frame End Mills: HSS 9mm wide x 95mm long
Polymer80 Pistol Frame Barrel Block Channel Sanding Kit -RefillsPolymer80 Pistol Frame End Mills: HSS 9mm wide x 95mm long

Hi folks, a customer asked if I could supply refill sanding cartridges for our Polymer80 Pistol Frame Barrel Block Saning Kit and the answer was "Sure - we definitely can" so here's the item so you can order them. The refill includes 8 sanding...

If you are doing a Polymer80 pistol build, they recommend using an end mill to remove the top tabs and/or cut out the barrel block they cast in the barrel channel of the frame. They used to include end mills and I always wished they were a tad...

$7.99

$14.99

Polymer80 Pistol Frame M35 Drill Bits - 3 & 4mm Polymer80, Glock and SIG Fire Control Group Wood Test Rod - 5"
Polymer80 Pistol Frame M35 Drill Bits - 3 & 4mmPolymer80, Glock and SIG Fire Control Group Wood Test Rod - 5"

These quality drill bits are sized for drilling Polymer80 pistol frames for their pins. This package includes one 3mm drill bit (approx 2.95-2.97mm) and one 4mm drill bit (approx 3.95-3.96mm). We have a blog post where you can read more if you...

I needed a better way to test the fire control groups of Polymer80, Glock and SIG pistols where I could not see what was going on in the slide - I could only go by sound and feel but I really wanted to get an idea of how firmly the firing pin or...

$6.99

$2.99